COSHH Assessment · Steeplejacks

COSHH Assessment for Steeplejacks

A COSHH assessment of the hazardous substances used or created, built from the product's Safety Data Sheet (COSHH 2002). For steeplejack work, it has to cover work at extreme height with fall from height risk. It must include each substance with its hazard statements and CAS number from the SDS.

A COSHH assessment of the hazardous substances used or created, built from the product's Safety Data Sheet (COSHH 2002). Below: what a steeplejack's COSHH Assessment must contain, why they get rejected, and the hazards it has to cover, or generate one for your exact job in a couple of minutes.

A finished example

Example COSHH Assessment from a similar trade (Electricians)

We do not have a finished COSHH Assessment for steeplejacks yet, so this one is from electricians: the layout, scoring and sign-off are what yours needs, but the hazards and method will be different for your job.

The job it was written for: “Substances used and created during installations, rewires, consumer-unit changes, testing and fault-finding. Commercial unit, occupied during working hours, 4 operatives, 2 days. Main risks: electric shock; working at height on steps and towers; asbestos in pre-2000 fabric.”. Names and contact details are anonymised.

EXAMPLE

COSHH Assessment, Example Electrician Ltd

Document TitleCOSHH Assessment
CompanyExample Electrician Ltd
Site AddressUnit 4, Example Trading Estate, Exeter EX2 8XX
Work ActivityInstallation, rewiring, consumer unit changes, testing and fault-finding.
AssessorA. Supervisor
Assessment Date14 October 2026
VersionV1.0
Review Date14 October 2027

1. Substances Assessed

This assessment is based on representative products. The Safety Data Sheet (SDS) for each specific product used on site MUST be available and consulted.

Product / Supplier Name (SDS §1)FormHazard Classification & Key H-Statements (SDS §2)Hazardous Ingredient(s) & CAS No. (SDS §3)Workplace Exposure Limit (WEL) from EH40/2005 (SDS §8)
WD-40 Multi-Use ProductLiquid / AerosolFlam. Aerosol 1: H222 Extremely flammable aerosol. STOT SE 3: H336 May cause drowsiness or dizziness. H229 Pressurised container: May burst if heated.Hydrocarbons, C9-C11, n-alkanes, isoalkanes, cyclics, < 2% aromatics (CAS: 64742-48-9)Long-term (8 hr TWA): 1200 mg/m³
Contact Cleaner / Switch Cleaner (e.g. Servisol Super 10)Liquid / AerosolFlam. Aerosol 1: H222 Extremely flammable aerosol. Skin Irrit. 2: H315 Causes skin irritation. STOT SE 3: H336 May cause drowsiness or dizziness. Aquatic Chronic 2: H411 Toxic to aquatic life with long lasting effects. H229 Pressurised container: May burst if heated.Naphtha (petroleum), hydrotreated light (CAS: 64742-49-0)Long-term (8 hr TWA): 1200 mg/m³
Cable Pulling Lubricant (e.g. Yellow 77)Gel / LiquidGenerally classified as not hazardous.Water based polymer lubricant.No WEL assigned, control exposure to As Low As Reasonably Practicable (ALARP).

2. Process-Generated Substances

SubstanceProcess Creating SubstanceHazard Classification & Key Health EffectsWorkplace Exposure Limit (WEL) from EH40/2005
Respirable Crystalline Silica (RCS)Drilling, cutting or chasing into concrete, brick, mortar, stone or other siliceous materials.STOT RE 1: H372 Causes damage to lungs through prolonged or repeated exposure (Silicosis). Carc. 1A: H350 May cause cancer.Long-term (8 hr TWA): 0.1 mg/m³
General airborne dust (non-silica)Drilling into plasterboard, wood, or other non-siliceous building materials.May cause irritation to the respiratory system and eyes.Long-term (8 hr TWA): 10 mg/m³ (inhalable dust); 4 mg/m³ (respirable dust).
Asbestos fibres (Presumed Present)Any disturbance of pre-2000 building fabric where an Asbestos Refurbishment & Demolition Survey is not available or is inconclusive.Carc. 1A: H350 May cause cancer. STOT RE 1: H372 Causes damage to lungs through prolonged or repeated exposure. H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.Control Limit: 0.1 fibres/cm³ over a continuous 4-hour period. Short-term exposure limit: 0.6 fibres/cm³ over a 10-minute period.

3. Who is Exposed and How?

Group ExposedRoutes of ExposureFrequency & Duration
Electrical Operatives (4)Inhalation: Dusts from drilling (RCS), vapours from solvents, aerosol mists. Skin Contact/Absorption: Direct contact with solvents, lubricants. Splashes to eyes. Ingestion: Transfer from contaminated hands to mouth.Intermittent use over two working days. Dust exposure is typically short but high intensity during drilling/chasing tasks.
Other Occupants in Unit 4Inhalation: Migration of dusts and solvent vapours from the immediate work area.Potentially for the duration of the work if control measures are inadequate.
Maintenance / Cleaning StaffInhalation / Skin Contact: Contact with settled dust or spills left after work is completed.Post-completion of works.

4. Risk Evaluation

The principal health risks arise from the inhalation of process-generated dusts, particularly Respirable Crystalline Silica (RCS) from drilling into masonry, which can cause irreversible lung damage and cancer. The risk is high without effective controls.

Inhalation of solvent vapours from cleaners and lubricants can cause dizziness and respiratory irritation. The risk is medium in poorly ventilated areas.

Skin contact with solvents can cause dermatitis. The risk is low with good working practices.

⛔ Asbestos: Any work on pre-2000 buildings carries a high risk of disturbing asbestos containing materials (ACMs). Accidental release of asbestos fibres presents a severe, life-threatening risk. This risk must be managed before any intrusive work begins.

5. Control Measures (COSHH Regulation 7 Hierarchy)

The following control measures are required. The responsible person must confirm they are implemented and maintained.

a) Prevention, Elimination or Substitution

  • Asbestos: Before any intrusive work, confirm the location and condition of any ACMs from the site's asbestos register and management plan, as required by the Control of Asbestos Regulations 2012. If no information is available, work must stop and a survey must be commissioned. Do not drill into any material suspected of being an ACM. All work on licensed ACMs is prohibited.
  • Substitute solvent cleaners with non-hazardous, water-based alternatives where technically possible.
  • Design cable routes to minimise the need for drilling into concrete or masonry. Use existing voids or surface-mounted trunking where feasible.

b) Engineering Controls (Control at Source)

  • Dust Control: For all drilling, chasing or cutting into masonry, concrete or brick, use on-tool extraction (M-Class or H-Class vacuum extractor) connected directly to the power tool.
  • Ventilation: Ensure good natural ventilation in the work area by opening windows and doors. For extensive solvent use in enclosed spaces, use mechanical ventilation.

c) Organisational / Administrative Controls

  • Restrict access to the immediate work area to essential personnel only.
  • Use screens or barriers to contain dust where practicable.
  • Implement wet-suppression techniques for dust control where on-tool extraction is not feasible (e.g. damping down surfaces before and during work).
  • Prohibit eating, drinking, and smoking in the work area.
  • Provide designated hand-washing facilities with soap and water.
  • Ensure operatives wash hands before breaks and after finishing work.
  • Rotate tasks between operatives to reduce the duration of exposure for any single individual.
  • Keep lids on all containers when not in use. Store aerosols and flammable liquids away from heat sources or sources of ignition.

d) Personal Protective Equipment (PPE) & Respiratory Protective Equipment (RPE)

PPE/RPE is the last line of defence and must be used in addition to the measures above, not as a replacement.

Substance / TaskRequired RPE / PPE (specify standard)
Drilling/cutting masonry (RCS)RPE: FFP3 disposable mask or half-mask with P3 filter (BS EN 149). Must be face-fit tested for the individual wearer. PPE: Safety glasses (BS EN 166).
Using solvent cleaners / aerosolsPPE: Nitrile gloves (BS EN 374), Safety glasses (BS EN 166). RPE: Required only if ventilation is poor and WEL is likely to be exceeded. Use organic vapour cartridge respirator (e.g. A2P3).
General dust (non-silica)RPE: FFP2 disposable mask (BS EN 149). PPE: Safety glasses (BS EN 166).
Handling cable lubricantsPPE: No specific requirement, but gloves may be worn for hygiene.

6. Exposure vs Workplace Exposure Limit (WEL)

With the engineering and organisational controls specified above implemented correctly, exposure to all substances should be controlled to well below their respective Workplace Exposure Limits. For substances without a WEL, exposure will be reduced to As Low As Reasonably Practicable (ALARP). For carcinogens (RCS, Asbestos), control must always be ALARP, even if below the WEL or Control Limit.

7. First Aid Measures (from SDS §4)

RouteFirst Aid Instructions
InhalationMove the person to fresh air and keep comfortable for breathing. If respiratory symptoms persist, seek medical attention.
Skin ContactRemove contaminated clothing. Wash skin thoroughly with soap and water. If skin irritation or rash occurs, seek medical advice.
Eye ContactRinse cautiously with clean water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists, seek medical attention.
IngestionDo NOT induce vomiting. Rinse mouth. Seek medical attention if you feel unwell.
Emergency ContactA. Supervisor, 01283 000000

8. Spillage & Accidental Release Measures (from SDS §6)

  • Small Spills (Solvents/Lubricants): Ventilate the area. Remove all sources of ignition. Absorb the spill with inert material (e.g., sand, granules) and collect into a suitable, labelled container for disposal.
  • Accidental Release of Asbestos: Stop all work immediately. Evacuate the area and prevent re-entry. Report immediately to the site manager and supervisor. The area must be assessed and decontaminated by a licensed asbestos contractor.

9. Handling, Storage & Disposal

  • Handling: Avoid contact with skin and eyes. Do not breathe vapours or dust.
  • Storage: Store all chemical products in their original, clearly labelled containers in a cool, well-ventilated area away from heat, direct sunlight and sources of ignition.
  • Disposal: All waste materials, including used containers, contaminated rags, and dust from vacuum cleaners, must be disposed of as controlled waste in accordance with local authority and Environment Agency requirements. Do not empty into drains.

10. Health Surveillance

Health surveillance under COSHH Regulation 11 is required for operatives with regular, ongoing exposure to Respirable Crystalline Silica. This includes periodic lung function tests. Records must be kept for 40 years.

11. Information, Instruction & Training

All operatives must be provided with:

  • A copy of this assessment and relevant Safety Data Sheets.
  • Information on the specific hazards and risks of the substances used.
  • Instruction and training on the correct use of control measures, including on-tool extraction and RPE.
  • Information on the signs and symptoms of exposure.
  • Training on emergency procedures.
  • Asbestos awareness training (UKATA or equivalent) is mandatory for any operative liable to disturb the building fabric.

12. Review

This assessment must be reviewed by the date specified in the header, or immediately if:

  • There is a significant change in the work process or substances used.
  • There is reason to suspect that control measures are no longer effective.
  • An incident occurs related to substance exposure.
  • New information on hazards becomes available.

Declaration and Sign-off

The responsible person confirms that the required actions have been completed, the control measures are in place, and the contents of this assessment have been communicated to all relevant personnel.

NameRoleSignatureDate
A. SupervisorSupervisor
Operative 1
Operative 2
Operative 3
Operative 4

What a compliant COSHH Assessment must contain

  • Each substance with its hazard statements and CAS number from the SDS
  • The Workplace Exposure Limit (EH40) where one exists, never invented
  • Controls in order of effectiveness, LEV and ventilation before RPE (COSHH 2002)
  • Process-generated substances screened (dust, fume, silica)

Why a steeplejack's COSHH Assessment gets rejected

  • Generic solvent boilerplate instead of the actual SDS hazards
  • A Workplace Exposure Limit fabricated for a substance that has none
  • Exposure risk credited mainly to gloves/masks (RPE is the LAST resort)
  • Process dust/fume (wood dust, welding fume, RCS) not assessed

Already have one? Check it against the standard, free.

Paste it below and it is scored the way an inspector would, with the failings that would get it rejected. No sign-up.

Steeplejacks hazards it must cover

Typical steeplejack work, meaning Inspecting, repairing and maintaining tall structures such as chimneys, steeples, towers and masts, working at extreme height using ropes, ladders or scaffold, brings hazards a COSHH Assessment has to address:

  • Work at extreme height with fall from height risk
  • Rope access and rigging equipment failure
  • Structural instability of deteriorating masonry or steelwork
  • Struck by falling debris or dislodged material
  • Lightning strike and adverse weather exposure at height
  • Asbestos in pre-2000 fabric of industrial chimney linings and flashings

Generate your COSHH Assessment in minutes

Built to the correct published standard for a steeplejack: specific controls, the right legal basis, a review date and a sign-off section you can operate.

Start your COSHH Assessment

FAQ

Do steeplejacks legally need a COSHH Assessment?

A COSHH assessment of the hazardous substances used or created, built from the product's Safety Data Sheet (COSHH 2002). For steeplejack work, meaning Inspecting, repairing and maintaining tall structures such as chimneys, steeples, towers and masts, working at extreme height using ropes, ladders or scaffold, it is the document a client, principal contractor or inspector expects to see, grounded in COSHH 2002 reg 6/7 (HSE), built from the product Safety Data Sheet.

What must a steeplejack's COSHH Assessment contain?

At minimum: each substance with its hazard statements and CAS number from the SDS; the Workplace Exposure Limit (EH40) where one exists, never invented; controls in order of effectiveness, LEV and ventilation before RPE (COSHH 2002); process-generated substances screened (dust, fume, silica).

Why does a steeplejack's COSHH Assessment get rejected?

The usual reasons: generic solvent boilerplate instead of the actual SDS hazards; A Workplace Exposure Limit fabricated for a substance that has none; exposure risk credited mainly to gloves/masks (RPE is the LAST resort); process dust/fume (wood dust, welding fume, RCS) not assessed.

Which regulation is a steeplejack's COSHH Assessment written under?

COSHH 2002. The full text is on legislation.gov.uk at https://www.legislation.gov.uk/uksi/2002/2677/contents.

How fast can I get a COSHH Assessment?

A couple of minutes. Describe the job, and RAMSReady writes a COSHH Assessment for your exact steeplejack job live against the correct standard, with a review date and a sign-off/records section.

Not writing this one today?

We will email you a one page overview of what RAMSReady covers, so you have it when you need it.

Want to see how it would work for your firm?

Tell us roughly what you run and who keeps your records, and we will come back to you.

Related guides

Other documents for Steeplejacks

Similar trades

Templates and tools